![]() ![]() If your system is connected to a monitoring center, an emergency report could be sent to that center. Ø Your system may not be programmed for these activations.įire Key – If programmed, you can activate the Fire alarm by pressing the Emergency Activation key for two seconds. Ø You must hold these keys for 2 seconds to activate these functions. NETWORX ALARM SYSTEM BEEPING CODE– The code pad will beep faster in the last ten (10) seconds as a warning. – Pressing the button will re-start your exit time, but you may only press the button TWICE. – (Example: Press the key for zone 4, press for zone 5.) The corresponding light for that zone will turn on when bypassed.Įxit Mode is used when you have already armed your Security System, but need to extend your exit time. (OPTIONAL) (The bypass light flashes.)ģ. Enter a 2-digit zone indicating the zone you wish to bypass. The following steps are used for bypassing zones:Ģ. Enter a. The corresponding light for that zone will go off when un-bypassed. – To manually un-bypass zones, perform the bypassing procedure on a zone that is already bypassed. ![]() – When your security system is disarmed, any zones that had been temporarily isolated or bypassed will be reset, and will therefore be protected when the system is armed again. – Once you have bypassed the zone(s) you may Arm the system via the or Mode. – If you wish to bypass one or more zones, this must be done while the system is in the disarmed state. For instance, a pet may need to be left in a part of the house that is usually protected. This is used to temporarily exclude one or more zones that would normally be protected. – If the red armed light is flashing during the entry delay, the alarm system has been activated in your absence. – If a valid code is not entered before the end of the entry delay, an alarm will occur. – After entering a valid code the red armed light will go off and the tone will stop. When you enter the protected area through one of the designated Entry/Exit doors, the code pad will sound a solid continuous tone for the duration of the entry delay, or until you enter a valid. – The light(s) corresponding to the bypassed zone(s) will illuminate, alerting the user that a zone(s) may be unprotected and can be faulted without an alarm. – The bypass light will illuminate if any zone(s) is bypassed. Listed below are the steps to arm in the PARTIAL Mode: PARTIAL is used when the user is inside the premise and wants protection around the perimeter. NETWORX ALARM SYSTEM BEEPING WINDOWSHome Mode is also used for protecting exterior doors and windows (the home perimeter) when the user is inside. For example, you may wish to exclude bedrooms at night when they are in use. Home Mode is an easy-to-use feature that allows you to temporarily exclude some rooms from security arming. Partial Arming the System – Partial or Home Mode: – The armed and exit lights will illuminate. – If the power light is off, you have no AC power. The security system will not arm if the ready light is not on. – If any zones are bypassed, a sensor in that zone can be violated without affecting the ready light. is used when the user is away from the premise and wants the interior protected. – The exit light will flash rapidly for the last 10 seconds of the exit delay as a warning to the user that the exit time is about to expire.įully Arming The System in Quick Arm Mode: – You may now leave the building via the designated exit path. Restore power if possible.Ģ. Enter your to arm the system. If the power light is off, you have no AC power. ![]() – Ready light will light when all protected zones and sensors are secure. ![]() Listed below are the steps to arm in the ON Mode:ġ. Close all protected doors and windows. ON is used when the user is away from the premise and wants the interior protected. Enter an area number from through to to select the area to view.Enter to access the change area function.To change the current code pad area view, follow the key sequence show below. Once an area view is accessed the code pad will revert to the default area view after 10 seconds unless a key is pressed, in which case it will only switch back 60 seconds from the last key press. In a multi-area system it is possible to control more than one area from the one code pad by switching area views. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |